Long Block (KB Olds, 4.440" x 4.250", intake to pan, repaired, CNC Dart 360 Heads with Crane Stud Girdles)

Long Block (KB Olds, 4.470" x 4.250", intake to pan, repaired, CNC Dart 360 Heads with Crane Stud Girdles) Click Here to See Details and lots of pictures

950,000 miles, Converted an titled as RV. 70" Condo sleeper with table and bench seats. Nice.

45' Kentucky with living quarters. The cargo area measures 24 feet 6 inches long. The inside width is 92" at the rear door. It is 10 foot 4 inches tall at the door, and 9 foot tall inside going over the wheel wells. Click here to see pictures. Click here to take a video tour.

Microquiet Generator (4000W, 120V only, electric start with remote start kit, exhaust pipe, Gasoline)

This is a MSD 8132 Pro Mag Tach converter. These allow a standard tach (like one that would attach to a old style distributer coil) to work with an MSD Pro Mag. They also allow a Data Recorder to attach to the Mag. They are used, but work well.

This is a set of 8 used aluminum blower studs. They are 7/16"x2.66", with 7/16-14 thread on the bottom and 7/16-20 thread on the top. Includes hardened 12-point nuts. One of the studs has been replaced with a blue one.

This is a set of 8 used aluminum blower studs. They are 7/16"x2.66", with 7/16-14 thread on the bottom and 7/16-20 thread on the top. Includes hardened 12-point nuts.

RCD part number 101307-03 engine stroker plate. This plate bolts to the front of a blower pulley and provides a 1/2" square hole for a socket wrench. Very Good condition.

Littlefield pulley, 26 tooth, 13.9mm pitch, 3 1/2" wide, but I ran them with 2 1/2" (65mm) belts. Good condition.

These were custom made for me by Gates. These are not comercially available. This is the new super strong carbon construction belts, but in the 1543-13.9-65HT style.

New Gates RCD 13.9mm 1543-13.9M-65HT Kevlar Blower Belt

Includes brackets, pins, and heat sheilds

Standard IH Style 100# suitcase weights

These are 15# weights made in the same general shape as a 100# IH weight, but made from 1/4" plate and trimed for proper weight. These were torch cut and powder coated.

2002 Joe Eder Chassis. NTPA certified rollcage, certified in 2007. Engler billet brake calipers. Magnesium CAT planetaries. Mico brake cylinders. Aluminum SQHD pig. Several gear ratios to choose from. Seat with 5-point harness. Fenders and back plate. Kill Switch. Throttle with cable splitter for up to 5 engines. Steering Rack with steering linkage. Weight brackets front and rear (up to 6 full size weights on each end). Battery mount. Banter Airplane front end. Clutch and engine mounts for side-by-side crank-to-crank engines. This chassis hooks hard and always pull straight.

Twin countershaft. Direct, +5%, +10%, Reverse. Neutral Safety and Reverse switches.

Attaches Holden Transmission to SQHD. Includes shielding.

Banter built. 1 5/8-16 input shaft, 2 1/16-32 output shaft, 36" input-to-input, 3 1/4" drop (input lower than output) - 54 tooth inputs, 44 tooth outputs.

Banter built. 1 5/8-16 input shaft, 36" input-to-input, 3 1/4" drop (input lower than output)

Full size upright injectors. Magnesium. Includes Enderle Barrell Valve, distribution block, fuel lines, nozzels, and jets.

Holds 20 (or 40 if using both sides) Enderle Jets

Wide w/EGT ports (2 1/2" pipe, 38" outside to outside mounted on tall deck Chevy)

Narrow w/EGT ports (2 1/2" pipe, 36" outside to outside mounted on tall deck Chevy)

Narrow w/EGT & O2 port (2 1/2" pipe, 36" outside to outside mounted on tall deck Chevy)

Computech Data Pro 45. Has enough inputs to instrument 2 V-8 engines. Includes display unit (about the size of a pack of cigarettes and is removable form the vehicle), Junstion box (were all the sensors connect), software, and manual. Sensors sold sepperately. I think this is the best system on the market. The display unit stores the data and is removable from the vehicle. You pop it off, and take in into your hauler or house to read the data. This eliminates the need to use your laptop out in the pit area where it can be damaged.

Boost, Oil Pressure, etc. Standard 4-20ma sensor. Includes pigtail, AN-3 fitting, and a length of braided steel hose.

Fuel pressure, etc. Standard 4-20ma sensor. Includes pigtail, AN-3 fitting, and a length of braided steel hose.

K-type thermocouples. Spaced for BBC headers, but would fit others. Does not include bungs to weld in, but those are commonly available.

Simple pickup. Senses one of more magnets. The magnets are perminately mounted in my equipment, so you will need to order some from Computech.